Jump to content

Railway gun

From Wikipedia, the free encyclopedia
(Redirected from Railroad gun)
French 370 mm railway howitzer of World War I

A railway gun, also called a railroad gun, is a large artillery piece, often surplus naval artillery, mounted on, transported by, and fired from a specially designed railway wagon. Many countries have built railway guns, but the best-known are the large Krupp-built pieces used by Germany in World War I and World War II. Smaller guns were often part of an armoured train. Only able to be moved where there were good tracks, which could be destroyed by artillery bombardment or airstrike, railway guns were phased out after World War II.

Design considerations

[edit]

The design of a railway gun has three firing issues over and above those of an ordinary artillery piece to consider. Namely how the gun is going to be traversed – i.e. moved from side to side to aim; how the horizontal component of the recoil force will be absorbed by the gun's carriage and how the vertical recoil force will be absorbed by the ground.[citation needed]

Methods of traverse

[edit]
Non-traversing (top); car traversing mount (middle); top carriage traversing mount (bottom)
British 12-inch howitzers on top-carriage traversing mounts, traversed 90°, Catterick, December 1940

The first method of traverse is to rely entirely on movement along a curved section of track or on a turntable with no provision to traverse the gun on its mount. The second is to traverse the rail car body on its trucks, known as a car-traversing mount. Generally this is limited to a few degrees of traverse to either side unless an elaborate foundation is built with a centre pivot and traversing rollers. The design of the foundation is the only limit to the amount of traverse allowed in this latter case. The third choice is to allow the separate gun mount to rotate with respect to the rail car body, known as a top-carriage traversing mount. This usually requires the gun to be mounted on a central pivot which, in turn, is mounted on the car body. With few exceptions these types of mounts require some number of outriggers, stabilisers, or earth anchors to keep them in place against the recoil forces and are generally more suitable for smaller guns. The American post–World War I assessment of railway artillery considered that the utility of even a small amount of traverse for fine adjustments was high enough that either of the two latter traversing methods is preferable to a fixed mount.[1]

Recoil systems

[edit]
Cradle recoil (top); top carriage recoil (second); sliding recoil (third); rolling recoil (bottom)

There are four primary methods to absorb the recoil force for railway guns: cradle recoil, top-carriage recoil, sliding recoil and rolling recoil.

Cradle recoil means that the gun recoils backward in its cradle, retarded and stopped by hydraulic buffers. It is returned to battery, or the firing position, by either helical springs or by air in a pneumatic recuperator cylinder that is compressed by the force of recoil. This is the most common method used for lighter railway guns and for virtually all field artillery designed after the French introduced their Canon de 75 modèle 1897.[citation needed]

Top-carriage recoil is the situation in which the gun is mounted in an upper carriage that moves on wheels on fixed rails mounted on the lower. The gun and upper carriage recoil together, restrained by the usual hydraulic buffers. Return to battery is effected either by gravity, through the use of inclined rails, which the gun and carriage have run up, by springs, or even by rubber bands, on some improvised mounts.[2] It is not well-suited to firing at steep upward angles because it cannot absorb much of the vertical component of the recoil force.[3]

This French 320 mm railway gun uses sliding recoil. The jacked-down sleepers are visible at full-size.

Sliding recoil has the car body sitting on a set of wooden crossbeams or "sleepers" placed underneath it which have been jacked down on to a special set of girders incorporated into the track so that about half the weight of the mount has been transferred to them from the trucks. The gun, car body and trucks all recoil together with the friction generated by the crossbeams sliding on the girders absorbing the recoil force after moving only about 1 to 2 metres (3.3 to 6.6 ft) to the rear. The sleepers must be jacked up again to allow the gun to roll forward to its firing position. This was often done by handwheels driving gear trains attached to the wheels, or even by electric motors on more modern mounts. Almost all of these type of mounts were of the non-traversing type and had to be fired from a curved section of track or turntable. The American post–World War I assessment of railway artillery praised its ruggedness, ease of manufacture and convenience in service, but acknowledged its unsuitability for smaller guns, due to excessive time of operation and lack of traverse, and that it was not suitable for the largest howitzers firing at high angles because of the enormous trunnion forces.[3]

With rolling recoil the entire gun, mount, and carriage rolls backward, typically between 30 and 50 feet (9.1 and 15.2 m), restrained only by the brakes. The mount was winched back into firing position by cables fastened to the track. This system was usually combined with cradle recoil because the springs of the trucks cannot withstand the vertical component of the recoil force alone. This type of mount was usually fitted with car-traverse. It was unsuitable for smaller guns due to the lack of traverse.[3] The great advantage of this method is that it requires minimal preparation and can fire from any suitable section of curved track.[4]

This French 274 mm howitzer used a combination of top-cradle and sliding recoil.

The methods were often used in combination with each other. Examples include the French 520 mm (20 in) railway howitzer which used cradle-sliding recoil. The American 14"/50 caliber railway gun Mark II used cradle-rolling recoil as did the 14 and 12 inch railway guns from Great Britain. Only the oldest weapons used a combination of top-cradle and sliding recoil. One example being the earliest mounts for the British designed BL 9.2 inch Railway Gun.[citation needed]

Anchorage

[edit]
No anchorage needed (top); truck platform anchorage (middle); ground platform anchorage (bottom)
French St Chamond 240 mm Canon de Mle 1893/96, WWI, using ground platform anchorage

The combination of rolling and cradle-recoil methods absorbed both the horizontal and vertical components of the recoil force and needed no special preparations, but all other types required some method to transmit the vertical force to the ground. One way is to build a platform on either the ties or the ground with girders, beams, pads or floats. The horizontal component would be alleviated by either sliding recoil or rail clamps, guys or struts to secure the mount in place. The French Schneider 194 mm (7.6 in) and 240 mm (9.4 in) mounts and the British 9.2 inch guns and 12 inch howitzers used rail clamps or guys. The American 8 in (200 mm) gun and the French 240 mm Canon de Mle 1893/96 M used struts.[4]

The other method is build a firing position and recoil pit (épi de tir in French) underneath the tracks, using either heavy timbers like the French 340 mm (13 in) and 400 mm (16 in) howitzers or an elaborate concrete or steel base. These latter were mostly used by the Germans for the 21 cm (8.3 in) and larger railway guns and by the French for their Batignollesmounts. Generally, for these emplacements the rails merely served to guide the gun into position and the gun was often mounted on a central pivot to allow up to 360° of traverse. The primary drawback of these positions was the lengthy time to build them.

History

[edit]

19th century

[edit]

The idea of railway guns was first suggested in Russia in 1847 by Gustav Kori (proposal),[5] followed by Ye. Repin (project, 1855), Pyotr Lebedev (who outlined the theoretical foundations of the railway artillery in Primeneniye Zheleznykh Dorog k Zashite Materika, 1857) and P. Fomin (developed a project of a large-caliber cannon, 1860).[6][7]

American Civil War

[edit]
A 32-pounder Brooke naval rifle railway gun used in the American Civil War
The "Dictator", Petersburg (Mathew Brady)

The first railway gun used in combat was a banded 32-pounder Brooke naval rifle mounted on a flat car and shielded by a sloping casemate of railroad iron. On 29 June 1862, Robert E. Lee had the gun pushed by a locomotive over the Richmond and York River line (later part of the Southern Railway) and used at the Battle of Savage's Station to interfere with General George McClellan's plans for siege operations against Richmond during the Union advance up the peninsula.[8]

Photographic evidence exists of at least one Union 13-inch siege mortar mounted on a rail car during the Siege of Petersburg. It was nicknamed the Dictator or the Petersburg Express.[9] When it was first fired, the recoil destroyed the flatcar on which it was mounted.[10] A flatcar strengthened by additional beams covered by iron plate was able to resist recoil damage from a full charge. The Dictator was then fired from a section of the Petersburg and City Point Railroad where moving the strengthened flatcar along a curve in the track trained the gun on different targets along the Confederate lines. The Dictator silenced the Confederate guns on Chesterfield Heights to prevent them from enfilading the right end of the Union line.[11] Another photo exists of a gun mounted on an armoured rail car with the caption of "Railway battery used in siege of Petersburg" although no textual evidence survives in support of the caption, which makes the claim that it is a photo of the Confederate gun from 1862 dubious.[citation needed]

France

[edit]

France also used improvised railway guns during the Siege of Paris (1870–1871).[12] In France, Lt. Col Peigné is often credited with designing the first railway gun in 1883. Commandant Mougin is credited with putting guns on rail cars in 1870. The French arms maker Schneider offered a number of models in the late 1880s and produced a 120 mm (4.7 in) gun intended for coastal defense, selling some to the Danish government in the 1890s. They also designed a 200 mm (7.9 in) model the Obusier de 200 "Pérou" sur affût-truck TAZ Schneider for Peru in 1910, but they were never delivered.[13]

United Kingdom

[edit]

The United Kingdom mounted a few 4.7 in (120 mm) guns on railway cars which saw action during the Siege and Relief of Ladysmith during the Second Boer War.[14] A 9.2 inch gun was taken from the Cape Town coast defences and mounted on a rail car to support the British assault on Boer defenses at Belfast, north-east of Johannesburg, but the battle ended before it could get into action.[15]

World War I

[edit]

The outbreak of the First World War caught the French with a shortage of heavy field artillery. In compensation, large numbers of large static coastal defense guns and naval guns were moved to the front, but these were typically unsuitable for field use and required some kind of mounting. The railway gun provided the obvious solution. By 1916, both sides were deploying numerous types of railway guns.[16]

France

During the First World War France produced more railway guns in more calibers and with different mountings than everyone else combined.[17] The largest French gun produce by Schneider of France the Obusier de 520 modèle 1916, a 20-inch (520 mm) railway "Fort Buster" to do what the German 16.53-inch Big Bertha had done at the outbreak of World War I and reduce the German forts in the final line of German defenses. One was destroyed in trials and the other did not complete firing trials prior to the signing of the Armistice. The gun remained in storage and was captured by the Germans during World War II. It later formed part of the German artillery complement during the Siege of Leningrad. The gun was disabled by a premature detonation and later abandoned.[18]

United States
WWI era U.S. Navy 14" railway gun at Sandy Hook, New Jersey

Baldwin Locomotive Works delivered five 14"/50 caliber railway guns on trains for the United States Navy during April and May 1918. Each 14"/50 gun [19] mounted on a 72-foot (22 m), 535,000-pound (243 t) rail carriage with four 6-wheel bogies was under the command of a United States Navy lieutenant with a standard U.S. Army 2-8-0 locomotive, a 10-ton crane car, two armored ammunition cars carrying 25 shells each, two cars carrying the recoil pit foundation materials, two fuel and workshop cars, three berthing cars, a kitchen car, a commissary car, and a medical dispensary car. A sixth locomotive pulled a headquarters car for Rear Admiral Charles Peshall Plunkett, with a machine-shop car, a spare parts car, a berthing car, a kitchen car, a commissary car, and a medical dispensary car.[20] After delivery by ship, these trains were assembled in St. Nazaire in August[21] and fired a total of 782 shells during 25 days on the Western Front at ranges between 27 and 36 kilometres (30,000 and 39,000 yd).[22] Each 14-inch (36 cm) projectile weighed 1,400 pounds (640 kg) and was fired at 2,800 feet (850 m) per second. The railway carriages could elevate the guns to 43 degrees, but elevations over 15 degrees required excavation of a pit with room for the gun to recoil and structural steel shoring foundations to prevent caving of the pit sides from recoil forces absorbed by the surrounding soil.[23] The trains moved cautiously because axle loading under the gun barrels was 50,330 pounds (22.83 t) while French railways were designed for a maximum of 39,000 pounds (18 t). These axle journals overheated at speeds of more than 10 kilometres (6.2 mi) per hour. After reaching its intended firing site and constructing the recoil pit, each gun could fire about two shells per hour. One of these guns was retained after the War as an ammunition test gun at the Dahlgren Weapons Laboratory until all United States battleships with 14"/50 guns were scrapped shortly after World War II.[20] The gun was then placed on display outside the U.S. Navy Museum at the Washington Navy Yard.[citation needed]

Baldwin constructed six similar gun carriages and two of an improved Mk II type[19] designed to permit firing the gun at all elevation angles without transferring weight to a separate foundation. These eight guns were completed too late to see combat, and were designated the 14-inch M1920 railway guns. Some were later stationed through World War II in special coast defense installations at San Pedro, California, (near Los Angeles) and in the Panama Canal Zone where they could be shifted from one ocean to the other in less than a day. Improved carriages were designed to allow their transportation to several fixed firing emplacements including concrete foundations where the railway trucks were withdrawn so the gun could be rapidly traversed (swiveled horizontally) to engage moving ship targets.[24]

After the American entry into World War I on 6 April 1917, the U.S. Army recognized the need to adopt railway artillery for use on the Western Front. No US railway guns existed at that time. Due to low production and shipping priorities, the Army's railway gun contribution on the Western Front consisted of four U.S. Coast Artillery regiments armed with French-made weapons. Three additional railway gun regiments were in France, but did not complete training prior to the Armistice, and they did not see action. Other Coast Artillery units also operated various types of French-, British-, and American-made heavy artillery.[25] The Army also converted some of the numerous coast artillery weapons to railway mounts. A total of 96 8-inch guns (including some from Navy spares), 129 10-inch guns, 45 12-inch guns, and 150 12-inch mortars could be spared from fixed coast defense batteries or spare stocks. Twelve 7-inch ex-Navy guns and six 12-inch guns being built for Chile were also available. To shorten a long story, none of these weapons were shipped to France except three 8-inch guns, as few of any type were completed before the Armistice. Forty-seven 8-inch railway guns were ordered, with 18 completed by the Armistice and a total of 37 (or 47, references vary) completed before the contract was canceled. Eight 10-inch railway mounts of 54 ordered were completed by the Armistice, and twelve 12-inch railway mounts were completed by 1 April 1919; the 12-inch contract was cancelled at that point. At least some of the 10-inch gun barrels were shipped to France and mounted on French-made carriages, but sources do not indicate any use of them in combat. Three railway mountings for the Chilean 12-inch guns were ready for shipment by the Armistice, and the remaining three barrels were kept as spares. A total of twenty-two 10-inch guns were eventually mounted. Ninety-one 12-inch railway mortars were ordered, with 45 complete by 7 April 1919 and the remainder eventually completed.[22][26]

The 7-inch and 8-inch guns and 12-inch mortars used a common carriage, with a depressed center and two 4-wheel or 6-wheel bogies. The bogies were interchangeable for standard-gauge or (with 12-wheel bogies) 60-cm (23.6-inch) gauge track.[27] Outriggers and a rotating mount allowed all-around fire. This allowed the weapons to be used in coast defense against moving targets. The 8-inch guns and 12-inch mortars were kept on railway mountings after the war, while almost all of the 7-inch, 10-inch, and 12-inch guns were returned to the coastal forts. With 47 available, plus an additional 24 ex-Navy Mark VI guns on railway mounts by 1942, the 8-inch guns were the most-commonly-deployed American railway gun through World War II. About 12 of these were used for the defense of Oahu, Hawaii. Others were stationed for the coastal defense of Manila (eventually dismounted from the railway carriage at Corregidor),[28] Bermuda, Newfoundland, Puget Sound, Chesapeake Bay, Delaware Bay, and Fort Hancock, New Jersey (near New York City).[29][30]

Although numerous 12-inch railway mortars were available, few were deployed. In 1930 the US Army tested them at Fort Hancock, New Jersey, and Fort Miles, Delaware.[31] During World War II, four railway mortars were among the temporary harbor defenses of Grays Harbor, Washington state, and emplacements for an additional four at Cape George, Washington, were constructed, but never armed.[32] Of the more than 250 railway guns built in the United States from 1916 to 1942, the five navy 14"/50 guns that were sent to France during World War I and possibly two 8-inch guns in the Philippines were the only ones ever to be used in combat.[20] Reportedly, the eight 8-inch railway guns in the Philippines in 1941–42 were either destroyed by air attack or lacked trained crews.[33][28]

World War II

[edit]

World War II saw the final use of the railway gun, with the massive 80 cm (31 in) Schwerer Gustav gun,[34] the largest artillery piece to be used in combat, deployed by Nazi Germany. After the Fall of France Germany added 58 captured French guns to its inventory while Italy was given 19 French guns with many of these being captured by the Germans after the Italian capitulation.[18]

Boche Buster, seen from Bourne Park Tunnel on the Elham Valley line, at Bishopsbourne in Kent, England, on 21 March 1941

Both Nazi Germany and Great Britain deployed railway guns that were capable of firing across the English Channel in the areas around Dover and Calais.[35] The Wehrmacht deployed three 40.6-cm (16-inch) guns.[36] The British Army deployed three 13.5-inch (34.3-cm) railway guns on the East Kent Light Railway, locating them around Lydden and Shepherdswell.[35][37][38] These were codenamed the "Gladiator", the "Sceneshifter", and the "Peacemaker".[35] 9.2-inch Mark 13 guns were located near Canterbury and Hythe, Kent; and 12-inch howitzers, Mk 3 and 5, located around Guston,[35] north of Dover on the Southern Railway line to Deal and Ramsgate.

The 18-inch howitzer "Boche Buster" was sited on the Elham Valley Railway, between Bridge, Kent, and Lyminge, and was intended for coastal defense against invasion. It was not capable of cross-channel firing, having a maximum range of only about 20 km (12 miles).


The IJA (Imperial Japanese Army) employed one railway gun, the Type 90 240 mm railway gun, which served as a coastal battery in the Tokyo bay, and was then stationed in Manchukuo, in the area of Heilongjiang. It was destroyed by the retreating Kwantung Army when the soviets invaded Mandchuria in late 1945.

Surviving railway guns

[edit]
A second 283 mm Krupp K5 can be seen at the Todt Battery museum, near Audinghen in northern France.[41]
  • Soviet-era 305 mm MK-3-12 guns are preserved at the Krasnaya Gorka fort near Lomonosov, Russia, and the Museum of Railway Technology, Saint Petersburg.
  • Soviet 180 mm ТМ-1-180 guns may be seen at Krasnaya Gorka fort, at the Museum of the Great Patriotic War, Moscow, and at the Railway Station in Sevastopol, Ukraine.
  • The last surviving American-made 7-inch (178 mm) railway gun is now on display at Museu Militar Conde de Linhares in Rio de Janeiro, Brazil.
  • While not a gun the Chehalis-Centralia RR of Chehalis, WA has something of great interest. It is a Model 1918 railroad car mount for a 12-inch seacoast mortar. These cars were built in the early 1920s to make obsolete seacoast artillery more mobile. While all the guns were scrapped in the early days of WW II this car survived at the Bremerton Navy Base.
  • There is an 8-inch gun on an M1918 Railway Mount, less car, at the University of Tampa, Tampa, FL.[42]

Images

[edit]

See also

[edit]

Citations

[edit]
  1. ^ Miller vol. I, p. 39
  2. ^ Miller vol. I, p. 52
  3. ^ a b c Miller vol. I, p. 65
  4. ^ a b Miller vol. I, p. 69
  5. ^ (in Russian) http://www.travelzone.lv/lib/zd_puski/index.php Archived 2013-07-03 at archive.today
  6. ^ Lebedev, P. N. (2011) [1857]. Применение железных дорог к защите материка. Сочинение инженер-подполковника П. Лебедева [Use of Railways for the Defense of Land. Essay of engineer-Lieutenant Colonel P. Lebedev] (in Russian). Moscow: Kniga po Trebovaniyu. ISBN 978-5-458-11821-7.
  7. ^ Denisov, A. P.; Perechnev, Yu. G. (1956). "Глава 4. Береговая артиллерия в Крымской войне 1853–1856 годов" [Chapter 4. Coastal Artillery in the Crimean War of 1853–1856]. Русская береговая артиллерия [Russian Coastal Artillery]. Moscow: Voenizdat. pp. 89–91.
  8. ^ Phillips, p. 225
  9. ^ Miller vol. I, pp. 9-16
  10. ^ Jack H. McCall, Jr., When Railroad Guns Ruled, Historynet; accessed 2017.10.29.
  11. ^ Miller, Francis Trevelyan (1957). The Photographic History of The Civil War. Vol. Five: Forts and Artillery. New York: Castle Books. pp. 51 & 54.
  12. ^ Tucker, S. C. (2005). The encyclopedia of world war I: A political, social, and military history. Abc-clio. ISBN 1-85109-420-2
  13. ^ Miller vol. I, pp. 17, 23
  14. ^ Miller vol. I, p. 23
  15. ^ Hall
  16. ^ Miller vol. II, pp. 1–186
  17. ^ Romanych, Marc (2017). Railway Guns of World War I. Heuer, Greg,, Noon, Steve. London: Osprey. p. 2. ISBN 978-1-4728-1641-2. OCLC 999616340.
  18. ^ a b Zaloga, Steve (2017). Railway guns of World War II. Dennis, Peter. Oxford: Osprey. pp. 2–3. ISBN 978-1-4728-1068-7. OCLC 907965829.
  19. ^ a b "The United States naval railway batteries in France". Internet Archive. 1922.
  20. ^ a b c Schreier, Konrad F. Jr. (1988). "Admiral Plunkett's Railway Battle Fleet". Railroad History. 158 (Spring 1988). The Railway & Locomotive Historical Society: 95–102.
  21. ^ Many, April 1965, p.53
  22. ^ a b Hogg, Ian V. (1998). Allied Artillery of World War I. Ramsbury, Wiltshire, UK: The Crowood Press, Ltd. pp. 138–148. ISBN 1-86126-104-7.
  23. ^ Westing (1966) pp.79-80
  24. ^ Lewis (1979) pp. 103, 106
  25. ^ "Defeating the Hun, The History of the U. S. Army, Coast Artillery Corps During WWI". ancestry.com.
  26. ^ "US Army Railway Artillery, WWI". ancestry.com.
  27. ^ Miller, H. W., LTC, USA Railway Artillery, Vols. I and II, 1921, Vol. I, pp. 131-155
  28. ^ a b Account of the 8" railway guns in the Philippines, 1940–42
  29. ^ Lewis (1979) pp. 102-110, 140-141
  30. ^ Berhow, pp. 199-228
  31. ^ "Mortar Railway Gun to Aid in Defending Coast" Popular Mechanics, December 1930
  32. ^ Berhow, pp. 216-217
  33. ^ The Doomed Philippine Inland Seas Defense Project
  34. ^ Zaloga (2016), pp. 14-15, 18-19
  35. ^ a b c d Arnold (1982), pp. 100, 108, 147, 148.
  36. ^ German 40 cm guns at Navweaps.com
  37. ^ Dale Clarke. "British Artillery 1914–19. Heavy Artillery". Osprey Publishing, London, 2005. Pages 41-42
  38. ^ "The Big Guns At Dover WW2 (World War Two)". Archived from the original on 2007-12-21.
  39. ^ Maev Kennedy (2 September 2013). "Giant first world war gun on the move across southern England this week". the Guardian.
  40. ^ Doyle, pp. 3
  41. ^ "Musée du Mur de l'Atlantique".
  42. ^ 8-inch Gun Railway Mount M1918

Bibliography

[edit]
[edit]